Can't find what you're looking for? Try our old website for IBECO.

Genomskärning av RSG flänspackning som visar gummiprofil med inbyggt stålinlägg

Flange gaskets RSG with steel insert for steel/cast flanges PN10/16 EPDM

EPDM

Flange gasket RSG with steel insert for steel and cast flanges PN10/16 in EPDM or NBR – easy centring and a tight flange with the correct torque.

38 varianter
4 dokument
6 certifieringar

About the product

RSG is a flange gasket with steel insert for steel and cast flanges in pressure class PN10/16. The steel insert gives the gasket rigidity, makes it easy to position correctly against the flange face, and protects the rubber from being squeezed out during tightening. The seal is EPDM and can also be supplied in NBR, with a hardness of 70 ± 5 Shore A and an operating temperature from -25 °C to +120 °C. The range covers sizes from DN 15 up to DN 2000. During installation, flange faces and bolts must be clean and undamaged, and the bolts should be lubricated with a suitable lubricant. Tighten crosswise in three steps, 30% / 40% / 30%, following the recommended tightening pattern with a torque wrench, finishing with a full circle at full torque. Separate torque tables are available for steel/steel and for PE/steel.

Variants(38)

Click a row for all details, or + to add it to the quote request.

Tightening torque steel/steel

Maximum tightening torque for the gasket for steel/steel

DN	PN6Nm	PN10Nm	PN16Nm	PN25Nm	PN40Nm
15	15	15	15	15	10
20	15	15	15	20	20
25	15	20	20	20	25
32	25	35	35	35	35
40	30	45	45	45	50
50	40	60	60	60	65
65	60	50	50	50	55
80	95	60	60	60	65
100	100	70	75	100	110
125	75	85	90	140	165
150	80	120	130	165	200
200	100	155	120	165	245
250	85	125	175	250	365
300	125	150	220	255	405
350	160	160	230	375	595
400	140	225	305	490	900
450	-	210	-	-	-
500	145	240	440	590	970
600	215	335	665	930	1680
700	220	385	580	1080	-
800	310	525	820	1620	-
900	370	580	845	1670	-
1000	365	740	1200	2360	-
1100	-	-	-	-	-
1200	510	1010	1690	-	-
1400	660	1250	1920	-	-
1600	730	1760	2700	-	-
1800	930	1920	2900	-	-
2000	-	2130	-	-	-

Tightening torque PE/steel

Maximum tightening torque for the gasket for PE/steel Comparison table PN10 vs PN16 – DN 50–1600 (EN 1092-1 bolting, K dimension; torque per DVS 2210-1 Suppl. 3)

DN	PN10 bolts	K(PN10)	PN16 bolts	K(PN16)	Torque per bolt Nm, DVS
50	4 x M16	125	4 x M16	125	20
65	4 x M16	145	8 x M16	145	20
80	8 x M16	160	8 x M16	160	20
100	8 x M16	180	8 x M16	180	20
125	8 x M16	210	8 x M16	210	30
150	8 x M20	240	8 x M20	240	30
200	8 x M20	295	12 x M20	295	35
250	12 x M20	350	12 x M24	355	40
300	12 x M20	400	12 x M24	410	45
350	16 x M20	460	16 x M24	470	50
400	16 x M24	515	16 x M27	525	60
450	20 x M24	565	20 x M27	585	65
500	20 x M24	620	20 x M30	650	70
600	20 x M27	725	20 x M33	770	100
700	24 x M27	840	24 x M33	840	100
800	24 x M30	950	24 x M36	950	100
900	28 x M30	1050	28 x M36	1050	100
1000	28 x M33	1160	28 x M39	1170	100
1200	32 x M36	1380	32 x M45	1390	100
1400	36 x M39	1590	36 x M45	1590	100
1600	40 x M45	1820	40 x M52	1820	100

- PN10 data (K, bolts) per Haihao/Hebei for EN 1092-1 PN10; PN16 data per RoyMech for BS EN 1092-1 PN16. - Torque per DVS 2210-1 Suppl. 3 (profile seal, µ≈0.15, lubricated threads/bearing surfaces). DN 450 = 65 Nm interpolated; DN > 600 = 100 Nm as an extended guide value. - The DVS values apply to PE flanges. Always follow the gasket manufacturer's specific instructions if they differ from the table

Material specification

Component	Material
Sealing body	EPDM
Insert	Steel
Sealing body, alternative (on request)	NBR

Certifieringar & standarder

SS-EN 681-1
DIN EN 1092-1

Document

Flange gaskets